glearn
AboutEventsCareersRegisterSign in
GLearn / Guides / WASSCE / Technical Drawing tips

WASSCE Technical Drawing

How to prepare for WASSCE Technical Drawing

How the objective paper, the geometry paper and the drawing paper differ, and the mistakes that cost marks. Practise with Kevin and Anna on glearn.now.

On this page+

    On this page

      A Ghanaian senior high school teaches the current NaCCA curriculum for senior high schools, senior high technical schools and STEM schools. Technical Drawing is a practical subject, and it is not General Knowledge in Art or the drawing strand in BECE Career Technology. WAEC sets the paper, GLearn Technologies writes this guide, and GLearn does not publish a pass rate.

      At a glance

      • Technical Drawing is built from constructions, sketches, and the drawing.
      • Vector geometry and first angle projection are part of the work.
      • Building drawing is one of the areas candidates revise.
      • Anna marks WASSCE answers on GLearn, and Kevin is the coach on BECE practice.
      • Read the WAEC Ghana timetable for your own series.
      • The WASSCE grade calculator adds an aggregate from grades you enter, and it does not check a result.

      Confirm details on the official page: WAEC Ghana timetable.

      Objective paper, geometry paper, and drawing paper

      The examination has three papers, and you take all of them. Papers 1 and 2 are a composite paper taken at one sitting. Paper 3 is the drawing paper.

      • Paper 1 is the objective paper. One part draws on plane and solid geometry, and every candidate answers it. Another part is a choice between building drawing and mechanical drawing.
      • You answer the part for the option you offer, not both. The front of the paper says which part.
      • Paper 2 is the essay and construction paper. The questions draw on plane geometry, solid geometry, and vector geometry. Vector geometry is set for candidates in Ghana.
      • The front of your paper says how many questions to answer. Extra unfinished constructions do not replace a required question you left blank.
      • Paper 3 is the drawing paper. It has a sketch section and a drawing section. The sketch section includes a compulsory sketch of an object, a component, a symbol or a tool, and a further sketch you choose.
      • The drawing section asks you to produce one drawing: either a building drawing or a mechanical drawing, not both. A second unfinished sheet does not replace the drawing you were meant to finish.

      WAEC Ghana WASSCE for schoolsWAEC Ghana timetableWAEC Ghana

      Topic areas to revise

      These are the areas candidates revise for WASSCE Technical Drawing. A heading is not a promise that every unit appears on your paper.

      1. 1. Instruments, lines, lettering and dimensioning

        A tee square, with its head against the working edge of the board, draws horizontal lines. Set squares on the tee square draw vertical lines and the angles they are cut to, including 30, 45 and 60 degrees. Lettering is freehand, between guidelines, at one height.

      2. 2. Plane geometry

        Bisect a line and an angle. Erect a perpendicular. Divide a line into equal parts or into a given ratio.

      3. 3. Solid geometry

        In first angle, the view is placed on the opposite side from the side you looked from. The plan goes below the front view, and the view from the left goes on the right. In third angle, the view is placed on the same side you looked from.

      4. 4. Vector geometry for Ghana

        Candidates in Ghana revise vector geometry for the essay paper. A resultant is the single force that can replace a system. An equilibrant is equal and opposite to the resultant and brings the system to rest.

      5. 5. Building drawing or mechanical drawing

        Offer the option you are entered for. Building drawing includes foundations and floors, doors, windows and arches, stairs, roofs, and working drawings: a plan, the elevations asked for, and a section, with the scale stated. Rise is the vertical part of a step.

      WASSCE syllabusPast questions with answersWASSCE Technical Drawing past questionsLines and letteringGeometrical constructionOrthographic projectionPictorial drawingSections and developmentsTechnical drawing basicsDrawing from observationBECE Career Technology tipsWASSCE Physics tipsWASSCE Visual Arts tips

      Constructions, sketches, and the drawing

      A construction mark is for a method a marker can see. A drawing mark is for a view that follows the brief.

      1. 1. Match the command

        Construct means show the construction. Draw means the finished view, to the scale, with instruments. Sketch means freehand, in proportion, with the right line types.

      2. 2. Leave the method visible

        Keep construction light, and darken the required outline at the end. A tangent, a locus, a true shape or a development with the construction erased cannot earn the method marks. If the question tells you to remove construction, follow that instruction and not this one.

      3. 3. State the scale and the angle

        Write the scale the question gives, and use it for every length. Write first angle or third angle in the title block, and do not mix them. On a force diagram, write the scale that turns a length into a force.

      4. 4. Label what the marker has to find

        Name the views: front, plan, end, auxiliary. Name the cutting plane. On a frame, name the member and say tension or compression.

      5. 5. On paper 3, obey the choice

        Do the compulsory sketch. Then do one other sketch if the rubric asks for one. Then draw either the building question or the mechanical question, not both.

      6. 6. Leave out the invented size

        A wall thickness, a rise, a tolerance or a force that the question did not give is not a result. Use the figure on the paper. If no figure is given, show the construction and the principle.

      WASSCE exam tipsPast questions with answersTechnical drawing basics

      How to use the time

      The clock is on the timetable and on the front of the paper. This page does not copy a duration.

      1. 1. Read the front before you draw

        Note how many constructions you may answer, and that paper 3 has a compulsory sketch plus one drawing. School candidates and private candidates follow the paper in front of them.

      2. 2. Start the hardest construction while you are calm

        A locus, a development or a vector diagram gets worse when you rush it. Give it a clean sheet area. An unfinished second attempt does not replace a required question you left blank.

      3. 3. Plan the sheet before you commit an outline

        Leave room for the title block, the border, and the views you must project. A drawing that runs off the sheet has not been planned. Draw the main view first, then project.

      4. 4. Treat paper 3 as its own paper

        Do the compulsory sketch first. Then the one drawing for your option. Do not start the other option because it looks shorter.

      5. 5. Leave a short check at the end

        Darken outlines. Add centre lines. Check that dimensions agree.

      WASSCE exam tipsWASSCE timetable

      A short way to revise

      Rotate the papers. A week of instruments with no vector work, or a week of sketches with no formal drawing, leaves part of the examination cold.

      1. 1. Give each paper a turn

        One session for objective items, one for a plane or solid construction from memory, one for a vector question if you sit the Ghana paper, and one for the option you offer: a building section or a mechanical assembly. Do the compulsory sketch from memory as well. Do not save paper 3 for the night before.

      2. 2. Close the book and construct

        Bisect an angle. Draw a tangent to a circle. Develop a truncated prism using true lengths.

      3. 3. Reject the wrong options

        On an objective item, say why the other options fail. A plan placed below the front view is first angle, not third angle. A hidden edge drawn as a thick outline is a reason to reject an option, not a detail to ignore.

      4. 4. Have the explanation marked

        Anna marks WASSCE answers on GLearn. Kevin is the coach on BECE practice. Write the steps of a construction in sentences and have them marked point by point.

      5. 5. Keep Technical Drawing inside the wider plan

        The revision plan orders the weeks across every subject you sit. Physics uses forces and moments in a different way, and it is not this paper. Career Technology at BECE has a drawing strand, and it is not this paper.

      WASSCE revision planHow to pass the WASSCEWASSCE Physics tipsTry WASSCE practice free

      Mistakes chief examiners keep returning to

      WAEC chief examiners write a report after a sitting. This page describes the habits in general, and it does not quote a report.

      1. 1. First angle mixed with third angle

        The plan is either below the front view or above it. The end view is either on the opposite side or on the same side. One sheet uses one system.

      2. 2. The wrong line, or no centre line

        An outline drawn thin, a hidden edge drawn solid, and a hole with no centre line are wrong even when the shape is right. Construction that is as dark as the outline hides the answer.

      3. 3. A construction with the method erased

        A locus, a tangent, a true shape or a development needs the construction. A fair curve alone has not shown the method, unless the question told you to remove it.

      4. 4. Dimensions that do not agree

        A chain of sizes that does not match the overall size, or a figure that ignores the stated scale, cannot all be right. Do not invent a millimetre the question did not give.

      5. 5. Both options attempted

        Building drawing and mechanical drawing are alternatives where the rubric says choose one. Two unfinished drawings do not replace the one drawing you were meant to finish. The compulsory sketch still has to be done.

      6. 6. A vector answer with no nature and no scale

        A force diagram without a scale is a picture. A member without tension or compression is unfinished. A shear force diagram that ignores a point load has not followed the question.

      Keep these open while you revise

      WASSCE practiceWASSCE syllabusPast questions with answersWASSCE Technical Drawing past questionsLines and letteringGeometrical constructionOrthographic projectionPictorial drawingSections and developmentsBECE Career Technology past questionsTechnical drawing basicsWASSCE Visual Arts past questionsDrawing from observationBECE Career Technology tipsWASSCE Physics tipsChoosing an SHS programmeWASSCE Visual Arts tipsWASSCE revision planHow to pass the WASSCEWASSCE exam tipsWASSCE timetableWASSCE grade calculatorWASSCE for private candidatesWASSCE General Knowledge in Art tipsCreate a free accountWAEC Ghana WASSCE for schoolsWAEC Ghana timetableWAEC Ghana

      Practise with Kevin and Anna

      Questions about WASSCE Technical Drawing

      What papers does WASSCE Technical Drawing have?+

      Three papers, and you take all of them. Paper 1 is objective. Paper 2 is plane geometry, solid geometry, and vector geometry.

      Do I answer both building drawing and mechanical drawing?+

      No. Where the paper offers the two as alternatives, you answer the option you are entered for. That applies to the choice on the objective paper and to the single drawing on paper 3.

      What is vector geometry, and who sits it?+

      It is the graphical treatment of forces, simple frames, shear force, bending moment, and the centre of gravity of a lamina. It is set for candidates in Ghana, on the essay paper. State the scale of a force diagram, and say whether a member is in tension or in compression.

      How do I set out a construction?+

      Read the command. If it says construct, leave the construction visible and light, then darken the required outline. State the scale and the angle of projection.

      What mistakes do chief examiners highlight in Technical Drawing?+

      Reports often describe first angle mixed with third angle, the wrong line type, a missing centre line, a construction with the method erased, dimensions that do not agree, both drawing options attempted, and a vector answer with no scale. This page does not quote a report and does not give a figure.

      Where do I practise Technical Drawing with Kevin and Anna?+

      Anna explains WASSCE answers. Kevin explains BECE answers, including Career Technology. Past questions are on the Technical Drawing hub, with pages for lines and lettering, geometrical construction, orthographic projection, pictorial drawing, and sections and developments.

      glearn

      Practise on GLearn

      Kevin and Anna explain every answer. The first questions need no account.

      Open past questions
      glearn

      Your coach for BECE & WASSCE. Built for every student in Africa.

      Study

      • Try it free
      • Sign in
      • Past questions
      • All guides
      • All comparisons
      • GLearn vs ChatGPT

      BECE

      • Your BECE aggregate
      • BECE results date
      • Choosing your schools
      • Checking your placement
      • Your SHS programme

      WASSCE

      • Your WASSCE aggregate
      • WASSCE results date
      • Checking your results
      • Resitting the WASSCE
      • Your WAEC certificate

      Company

      • About us
      • The company
      • Press
      • Events and stories
      • Become an ambassador
      • Join the team

      Featured on

      • Featured on Twelve Tools
      • Launched on Fazier
      • Listed on AINavDir
      • GLearn is featured on SpacerrApps

      © 2026 GLearn Technologies · San Francisco, California, USA

      PrivacyTerms